EHK Trigger Clamp
Product details
- Clamping force from 40 lbs to 600 lbs
- No tools required for conversion to spreading
- Available in sizes from 4.5 In to 50 In
- Soft-touch jaw pads eliminate marring of work
- Ergonomic composite handle
= Show Spareparts
| Order number | Clamping capacity | Throat depth | Spreading capacity | Clamping force | Approx. weight |
| inches | inches | inches | lbs | lbs | |
|---|---|---|---|---|---|
|
EHKMICRO
|
4 1/2 | 1 5/8 | 3 - 7 3/8 | 40 | 0.13 |
|
EHKM06
|
6 | 2 3/8 | 4 3/4 - 10 1/2 | 100 | 0.69 |
|
EHKM12
|
12 | 2 3/8 | 4 3/4 - 16 1/2 | 100 | 0.84 |
|
EHKL06
|
6 | 3 1/8 | 6 1/4 - 11 3/4 | 300 | 1.27 |
|
EHKL12
|
12 | 3 1/8 | 6 1/4 - 17 3/4 | 300 | 1.49 |
|
EHKL18
|
18 | 3 1/8 | 6 1/4 - 23 1/2 | 300 | 1.7 |
|
EHKL24
|
24 | 3 1/8 | 6 1/4 - 29 1/2 | 300 | 1.9 |
|
EHKL36
|
36 | 3 1/8 | 6 1/4 - 41 1/2 | 300 | 2.32 |
|
EHKXL06
|
6 | 3 5/8 | 7 1/2 - 12 1/4 | 600 | 2.37 |
|
EHKXL12
|
12 | 3 5/8 | 7 1/2 - 19 1/4 | 600 | 2.74 |
|
EHKXL18
|
18 | 3 5/8 | 7 1/2 - 24 1/4 | 600 | 3.1 |
|
EHKXL24
|
24 | 3 5/8 | 7 1/2 - 31 1/8 | 600 | 3.46 |
|
EHKXL36
|
36 | 3 5/8 | 7 1/2 - 42 3/4 | 600 | 4.18 |
|
EHKXL50
|
50 | 3 5/8 | 7 1/2 - 56 1/4 | 600 | 5.07 |
- Furniture and joinery works
- Kitchen construction and shop fitting
- Staircase construction
- Interior fittings
- Dry construction
- DIY
- One-handed clamping and spreading
- Use the product only in its original condition.
- Use the product only for its intended purpose. Improper use can cause personal injury or property damage.
- Wear safety goggles to protect your eyes.
- Wear protective gloves to protect your hands.
- Wear safety footwear to protect your feet.
- The handle must always be free of oil and grease to prevent slipping.
- Keep the product out of reach of children.
- Small parts must not be swallowed or inserted into body openings.
- Check the product for damage before each use and make sure that all moving parts are working properly.
- A damaged product must not be used.
- Follow the care instructions for each product – see www.bessey.de.
- Use only original BESSEY spare parts.
- The Clamping tool must not be used for lifting, pulling or leaning.
- The clamping tool must not be used to secure cargo during transportation.
- The clamping tool may only be tightened by hand without any additional aids.
- The clamping tool must not be used for permanent installation.
- Regularly check that the end stop is working properly when using clamps.
- Upper and lower section made of reinforced PA6 plastic
- Rail made of hardened steel, burnished
- Lever made of reinforced PA6 plastic
- Plastic protective cap helps prevent surface damage during use
- Regular maintenance is essential to ensure a secure hold and prevent the sliding arm from slipping.
- Clean the rails using a suitable solvent to remove dirt and debris.
- Keep the rail free of contaminants such as grease, oil, dried glue, wax, and silicone-based release agents, as these can affect performance.
